Development Sites Sydney: Find Sites Ready to Build With BuilderApp Property Finder

Finding development sites Sydney investors actually want usually means weeks of scrolling listings that were never built for developers. BuilderApp’s new Property Finder changes that. It shows properties ready for development, so you start with sites that can work.

Aerial view of a suburban housing development

The problem with searching for development sites Sydney

Mainstream property portals are built for home buyers. They show bedrooms and kitchens, not zoning, lot size or frontage. Developers end up checking each listing by hand, one council map at a time.

Property Finder starts from the other end: sites with development potential first.

How to find development sites Sydney with Property Finder

What makes a good development site in Sydney?

  • Zoning that allows your plan: check it on the NSW Planning Portal Spatial Viewer
  • Enough lot size and frontage: councils set different minimums (see our dual occupancy lot size guide)
  • Few constraints: heritage, flooding, bushfire and easements all add cost and time
  • Good access: services, driveway and construction access
  • An end value that works: what the finished homes will sell or rent for
Tower crane on a property development site

Strategy

Typical zoning

What to check first

Dual occupancy (duplex)

R2 or R3

Council minimum lot size and frontage

Terraces / townhouses

R3

Density controls and site width

Subdivision

R2 or R3

Minimum lot size after subdivision

Granny flat

R2 and others

Lot size, setbacks and access

6 checks before you make an offer on development sites Sydney

A search result is a starting point, not a green light. Before you make an offer on any of the development sites Sydney listings you shortlist, work through these six checks:

  1. Zoning and the land use table: confirm the zone, then read the land use table in the council’s Local Environmental Plan (LEP) to see what is permitted with consent.
  2. Lot size and frontage: compare the site against the minimums in the LEP, the council’s Development Control Plan (DCP) and any state policy that applies.
  3. Planning certificate: order a section 10.7 planning certificate from council. It shows the zoning and planning controls that apply, plus hazards such as flood or bushfire where they are recorded.
  4. Constraints: look for heritage listings, flooding, bushfire, trees, slope and easements. Each one can add cost, time or design limits.
  5. Services: check sewer, water and stormwater connections, and whether a main runs through the block.
  6. Title: review the title search for covenants, easements and restrictions on use.

How NSW housing reforms affect development sites Sydney

The NSW Low and Mid-Rise Housing Policy changed what some sites can deliver. Dual occupancies are now permitted with consent in R2 zones state-wide. In Low and Mid-Rise Housing areas, a dual occupancy has a minimum lot size of 450 m² and a minimum lot width of 12 m.

Terraces are also permitted with consent in R2 zones within 800 metres walking distance of a nominated town centre or station entrance. The standards there include a 500 m² minimum lot size and an 18 m minimum lot width.

Council rules still apply on top, so always confirm the controls for the exact address. Read the NSW Government summary of key provisions for the full detail.

From site to build in one platform

Property Finder is step one. BuilderApp then helps you check the site, cost the project and hire the builder:

  1. Find: Property Finder
  2. Check: Feasibility
  3. Cost: Cost Estimator
  4. Build: post a job for builder quotes

Start searching development sites Sydney today

Stop filtering home listings by hand. Search development sites across Sydney and check each one in minutes.

Search development sites →

Got questions

A search tool that shows properties ready for development starting with Sydney during our pilot.

 Check the zoning, lot size, frontage and constraints. BuilderApp Feasibility gives you a quick summary, and a town planner can confirm.

Dual occupancy is usually permitted in R2 and R3 zones, but each council sets its own minimum lot size and frontage.

Open Property Finder to see the current access options before you start your search.

Contact BuilderApp

Questions about this article, or need help finding a builder or tradie in Sydney? Call, email or send us a message and our team will get back to you.

    Need a builder or tradie?

    Post your job free and local trades can respond. During our Sydney pilot, expect one or two responses.